Motor Accessories

Motorbike modelling in Pavia

We offer a great range of motorcycle modelling accessories to accompany our model motocycles. New Faor offers solutions for every need and are able to satisfy the wishes of the most demanding enthusiasts.
dei ricambi di un modellino

KIT PLATES ADJUSTABLE FORCELS FOR CROSS

Adjustable plate kits made from full CNC. The key advantage of this kit is to stretch or shorten the motion range within a few minutes with a simple screw adjustment. With this plate you will have the bike with the correct wheelbase for any circuit. It will shorten the motorcycle's distance to short or twisted circuits and extend the distance circuit for fast circuits.
l’asse delle ruote di un modellino di una macchinina

KIT PLATES ADJUSTABLE FORWARDS FOR ENDURO

Adjustable plate kits made from full CNC. The advantage of this kit is to be able to stretch or shorten the travel distance within a few minutes, with the simple adjustment of a screw. With this plate you will have the bike with the correct wheelbase for any circuit. It will shorten the motorcycle's distance to short or twisted circuits and extend the distance circuit for fast circuits.
le corone di un ricambio di un modellino di una moto

FRONT DOUBLE DISC BRAKE SYSTEM FOR CROSS / ENDURO

Innovative braking system front. The double disc plant weighs like the monodiscal system, as it uses discs with lower dimensions, thus greatly reducing the gyro force acting on the front wheel. It allows to brake in the dirt without danger and facilitates the speed in the curve.

YAMAHA FRONT HORSE produced by CNC

MOZZO ANTERIORE YAMAHA prodotto a CNC

FRONT HOLE HONDA CRF-250-450 CNC

FRONT HOLE HONDA CRF-250-450 CNC product. Available in both the 2013 and the previous versions from 2008 to 2012

Piastra regolabile

Adjustable plate kits made from full CNC. The key advantage of this kit is to stretch or shorten the motion range within a few minutes with a simple screw adjustment. With this plate you will have the bike with the correct wheelbase for any circuit. It will shorten the motorcycle's distance to short or twisted circuits and extend the distance circuit for fast circuits.

REAR HUB PIT BIKE CNC

REAR HUGE PIT BIKE. The main feature is the use of 2 crown side bearings. CNC product

Pit Bike Clutch

PIT BIKE CLUTCH IN ERGAL 7075 ANODIZED DYE FOR LIFAN MOTORS - YX - GPX - DAYTONA - TAKEGAWA

REAR HUB SUZUKI CNC

REAR HUGE SUZUKI produced at CNC

FRONT HOLE HONDA CRF 150 CNC

HONDA CRF 150 FRONT HORSE. Main feature is the use of bearings larger than the original 15x35x11. CNC product

HEAT EXCHANGER

Heat exchanger

TCS plate

The TCS plate is used in Supermoto to make the front axle more rigid. With this plate you will have the advantage of not pushing the curbside forward by twisting the forks, but above all you will not have the floating effect of the wheel and fork. They fit all the forks with the reduction bushes

SERIES COLORED ERGAL SERIES WITH REINFORCEMENT

SERIE MANUBRI IN ERGAL COLORATI CON RINFORZO

FRONT PIT BIKE CNC HUGE

MOZZO ANTERIORE PIT BIKE CNC
dei chiodini bordeaux

ERGAL 7075 SCREW KIT FOR HONDA - CARTER CLUTCH

Screw Ergal kit 7075 for Honda. The kit includes: Clutch screws, Screws for clutch cover Screw for oil level
dei chiodini bordeaux

ERGAL 7075 SCREW KIT FOR HONDA - BOBINA-LEVER GAS-LEVER CLUTCH etc.

Screw Ergal kit 7075 for Honda. The kit includes: Reels and accumulator screws Rear bumper screws Screwdriver screws Screws for sprocket cover Screw clutch screws Gas lever screws Brake lever screws Chain drive screws Engine tensioning screws

DISCO FRENO MOTARD FLOTTANTE diam. 240mm

MOTOR FERROW FRONT DISK DISC MOTOR diam. 240 for PIT BIKE

NEW REGULATED COLORED PLATES

NEW - Adjustable plates for CROSS and ENDURO anodized in BLUE, ORANGE, RED and BLACK

FRONT HULL TRIAL

FRESH TRIAL FOR BETA
le corone di un ricambio di un modellino di una moto

DOUBLE FRONT DOOR BRAKE SYSTEM - CROSS / ENDURO

DOUBLE FRONT DOOR BRAKE SYSTEM FOR SUPERMOTO Anodised aluminum fork stand with n. 2 disks in diameter 240mm. Constructive features 1) Less weight: it is one of the lightest present up to now in Supermoto. Compared to a common monodisc with a diameter of 310mm or 320mm, it saves from 400g to 750g depending on diameter 2) Equal weight distribution: Caliper feet have the same weight that is equally distributed on both fork stems. The monodisco only loads the left stem Advantages • Improved sliding of the stem in the fork • Less left bending left in the stakes • Less wear on the left fork bushes, therefore less maintenance 3) Turning the front wheel: can be mounted In both directions. For example on a track with many curves right after a few turns you can turn the wheel without disassembling the tire Dynamic Features 1) Gyro Effect: The 310 / 320mm diameter monodisc weighs from 1.150g to 1.600g by diameter, against 900g Total of 2 disks with 240mm diameter. A smaller mass and diameter diminish the forces that tend to straighten the fold motion and turn the wheel in the direction of the curve. The sensation is that of a lighter, more agile and maneuverable bike 2) Brake down the curve: the aforementioned effects favor the insertion in the curve, allowing to delay the detachment and increase the input speed in the curve 3) Greater Confidence: our double disc is less aggressive and more progressive than monodisc, easier to handle on wet and dirt. You can lock the front wheel into the ground without the bike jamming. Conclusion All these benefits will lead to an improvement in lap times. Indeed anyone who has used this system has lowered his time by improving even the various personal records on the Motard run.

FRONT HORN KTM 990 CNC product

MOZZO ANTERIORE KTM 990 prodotto a CNC

REAR HUB KTM 990 CNC

MOZZO POSTERIORE KTM 990 CNC

A wide selection of spare parts and accessories for motorcycles: for information, info@nuovafaor.it

Share by: